Getting Started with Plumbing Basics When Installing a Bathtub
Getting Started with Plumbing Basics When Installing a Bathtub
Blog Article
What're your thoughts about Installing A Bathtub?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bath tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and also often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately difficult task. If the old bathtub is readily obtainable, the task can move rapidly; if you have to open up a wall surface to eliminate the old bathtub and also position the new bath tub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and fit attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is better to consider employing one before you start. Chances are you may need a specialist plumber to make tube connections.
This short article will certainly help you set up a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools and also product checklist should consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the restricted access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in place between the tap and also the sink. Protect the faucet in place with the maker provided backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The former type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using the two wooden boards under its feet, position the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub till the level reviews level.
To install faucets, fit all-time low of the outermost versatile faucet connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Activate the supply of water and inspect all joints and brand-new pipework for leakages as well as tighten them if needed. Fill the tub and also check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub must wait until the bath tub has actually been used at the very least once as this will certainly settle it into its final setting.
Preparing for the Installment
Firstly, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final placement.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break an inflexible seal, causing the water to penetrate the wall between the bath and the tiling, resulting in complications with dampness as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily readily available on the market. It is advisable to fit the tiles making use of water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place a remark down the page. We'd be glad to find out your ideas about this piece. We hope that you visit us again in the near future. So long as you appreciated our article please make sure you remember to share it. Thanks a lot for your time. Visit us again soon.
Excellence? Just call! Report this page